It’s usually located near the fireplace, usually to the immediate left, right or on the floor. You will control the gas flow with a fireplace key (sometimes called a hex key) as you light the fireplace.
Where are gas valves usually located?
Your main shut off valve is located just before the gas meter. This is called your “street side valve”. On the inside of your house, where the pipe enters your house, you can find your “house side valve.” This ball valve is attached to a black iron pipe.
How do I turn on my gas fireplace valve?
- Look over the user manual included with your fireplace. …
- Remove your fireplace’s outer cover. …
- Put a fireplace key into the device’s gas valve knob. …
- Hold a long lighter up to the burner and ignite it. …
- Turn the gas key. …
- Replace the fireplace’s outer cover immediately.
Where should a gas shut off valve be located?
The gas meter and gas service shutoff valve is usually located on the side or in front of the building. If the building has a breezeway, it could be located there.Does a gas fireplace require a shut off valve?
As adopted and amended by 248 CMR, NFPA 54, National Fuel and Gas Code, outlines specific requirements for natural gas appliances such as outdoor fireplaces and grills. One such requirement is the need for an accessible, approved manual shutoff valve approved by the AHJ prior to installation.
How do I know if my gas valve is off or on?
Gas shutoff valves When the long side of the nub or handle is parallel to the incoming gas line, it’s open and the gas is flowing. When it’s turned a quarter turn, perpendicular to the incoming pipe, it’s closed.
What does the gas valve look like?
Main Gas Shutoff Valves The valve will usually look like a small rectangle, and you’ll need a special wrench to turn it. When it’s open, the long side is parallel to the incoming gas pipe. … To shut off the gas supply to your house, use the house-side main valve (older homes may not have one).
How do you test a gas fireplace valve?
A digital multimeter can be used to check the voltage in the presence of a pilot flame as well as test for a drop in potential when the main valve is activated. This can be done by locating the red and white wires connected to the TP/TH and TP terminals on the main control valve.How do you know if a valve is open or closed?
Ball valves are perhaps the easiest valve to see if they are open or closed. If the handle on top is parallel to the valve, it’s open. Likewise, if the handle is perpendicular to the top, the valve is closed.
Why is my gas fireplace not lighting?If gas is coming out of the pilot, but it still won’t light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. … The pilot lighting, but not staying lit, indicates that the thermocouple is worn out, Worthen says.
Article first time published onShould I turn off the pilot light on my gas fireplace in the summer?
Your Utility Bill Perhaps the most important reason to turn off gas fireplace pilot light in summer is because of the money and energy you will be saving. If you leave the pilot light on during the summer it is simply sitting there burning gas, which is wasting gas and contributing to an exorbitant energy bill.
Why does a gas valve fail?
The valve itself may have simply worn out or may be damaged due to basement seepage or submersion. Alternately, one of the electronic gas ignition components or a glitch in the safety circuit may be to blame. If your furnace has a standing pilot light, the thermocouple could be worn out.
What is a seismic gas shut off valve?
Earthquake natural gas shut-off valve (also known as a seismic natural gas shut-off valve) automatically shuts off your natural gas service when an earthquake of a sufficient magnitude occurs at your home.
How do I know if my gas fireplace valve is bad?
One way to test if your main control valve is bad is by testing resistance. We can do this with our Digital Multimeter. First, find you need to find “Zero” but touching your multimeter leads together. If it reads anything other than zero, you’ll want to subtract this number from the number you will read on the valve.
How do I know if my gas fireplace is on?
Gas Fires. If your fireplace has ceramic logs in the firebox, it burns gas! There should be valves, a gas connection, an ignitor, a control knob, and maybe even a remote control. It’s important to figure out quickly whether your gas fireplace is vented or vent-free.
How do you know if your gas fireplace is gas?
You might want to use a flashlight so you can see well. Most modern gas logs have an igniter button which will be a little red button. It’s the same kind you would see on a gas grill. If it doesn’t, you’ll need a long lighter or fireplace matches to light the flame.
How do you turn off a gate valve?
Gate valves close by turning the wheel clockwise until the water is off. Ball valves close by turning the straight handle a quarter turn clockwise until the water is off.
What happens when gas is shut off?
If the pilot light is not lit, the gas burner will not ignite, which could cause a dangerous situation by letting highly flammable gas escape into the air. … If your gas is shut off, turn the gas shutoff valves on all gas appliances to the “off” position until the gas service is restored.
How much does it cost to replace a gas shut off valve?
Installation of a gas shut-off valve costs between $300 and $500. Depending on the pipe size, the valves cost between $100 and $300. You’ll pay an additional $150 to $200 for labor and other supplies.
How long do gas fireplace valves last?
Gas fireplaces are appliances, and like any other appliances, they have an expected lifespan for parts and for the entire unit, depending on the type of appliance, location, amount of use, etc. Thermocouples, thermopiles and pilot assemblies usually last at least five years, and control valves seven to ten years.
How does a gas valve work on a gas fireplace?
Gas flows into a series of valves attached to your gas fireplace. The valves are always closed unless something opens it. This prevents gas from flowing into your home when the fireplace is not lit. A device called a thermocouple will hold open the pilot light valve as long as the pilot light is lit.
How do you bleed air from a gas fireplace?
While pressing the valve control knob in, press the igniter button repeatedly until the pilot ignites. This could take anywhere from one to 10 minutes to bleed air out of the lines as the gas starts to flow. Once the pilot is lit, continue to press the valve knob inward for 30 seconds before releasing it.
Does the pilot light always stay on in a gas fireplace?
Should the pilot light always be on in a gas fireplace? Most gas fireplaces rely on a “continuous pilot light,” a type of pilot that remains lit so long as gas is flowing to the unit. … If you have a continuous pilot light system, you should always see a pilot flame unless you have manually turned the system off.
How much does it cost to run a pilot light on a gas fireplace?
A pilot light is a small flame that is kept lit to provide a catalyst for the main burner to be turned on when needed. The average fuel consumption of your standing Pilot light is: Natural gas is $0.60 a day = $219 a year.
Do gas fireplaces burn a lot of gas?
Not at all. Using natural gas is one of the most inexpensive ways to heat your home. That’s why gas fireplaces, gas fireplace inserts, outdoor gas fireplaces, even gas furnaces are such cost-effective heating options. Realistically, most gas-powered fireplaces will burn through about $1 worth of natural gas per day.
How long do gas valves last?
Gas Valves are routinely checked for 100,000 cycles and are used in equipment that have approximately 15 years life expectancy.
Can a gas valve be repaired?
In some instances you can repair a gas valve on a furnace depending on what is causing it to not work properly. However, repairing your gas valve is not usually the most cost effective option since it can be just as expensive to have your gas valve repaired as it would be to have your entire gas valve replaced.
Do gas valves fail?
Although relatively rare, gas valves can fail causing a fire or explosion. Gas valves can fail from a variety of causes including contamina- tion, product deficiency, and misuse.
