Cetol Marine can be applied anywhere that you would use varnish, but is particularly suitable for areas that endure hard use—grabrails, swim platforms and ladders, or the cockpit sole, where it produces a surprisingly durable and non-slip finish. … Unlike varnish there is no need to sand between coats.

Is sikkens a varnish?

A medium build, solvent-borne interior varnish that is resistant to knocks, spills and abrasion.

Can you put varnish over cetol?

Varnish will go over a thin coat of Cetol but not the other way around. Varnish is much harder and more abrasion resistant.

Is cetol a polyurethane?

polyurethaneacrylic resin-basedfor wood.

What is sikkens cetol?

Sikkens Cetol SRD is a one-coat, translucent exterior wood finish created for use on a wide variety of surfaces. The easy-to-use finish has excellent UV protection and allows beautiful wood clarity.

How many coats of cetol are there?

Cetol 1 is always used as the first coat in any bare wood application. All systems consist of three coats. All three coats must be applied within 30 days after preparation.

Can you use cetol over stain?

It is recommended that Cetol Marine be applied directly to bare wood, or to a previously applied Cetol Marine finish that’s in good condition, and not to stain or wood finishes other than Cetol Marine. …

Is sikkens cetol oil-based?

Sikkens Proluxe Cetol SRD is a one coat, oil-based, translucent exterior wood finish. Sikkens Proluxe Cetol SRD was created for use on a variety of wood surfaces including siding, rails, decks, and logs.

How long does cetol last?

Cetol is the toughest finish on the market…it will last three years at least. So you can have a good looking boat redoing the teak every three years or have a real good looking boat by oiling it every four to six months.

How long does sikkens cetol last?

Sikkens states in their literature that you should expect to get 2-4 years life out of their system on a sunny side of a house, and 3-5 years on a shady side. At this point, maintenance should be performed. Maintenance is cleaning the surface gently with bleach, TSP, and water.

Article first time published on

Does sikkens make a clear coat?

Sikkens Proluxe Cetol Maintenance RE Clear Topcoat is available in a satin finish for maintenance applications.

How do you use cetol in the Marines?

Keep a wet edge to prevent lap marks and thoroughly saturate end grains where possible. Apply 3 coats of Cetol® Marine. Always allow 24 hours drying time in between coats. Sanding between coats is not recommended as this will result in a reduction of dry film thickness.

What is the difference between cetol 1 and cetol 23?

Cetol 1 is a premium, translucent exterior wood basecoat to be used with Cetol 23 Plus. Its superior oil alkyd formulation offers excellent penetration and adhesion to vertical wood surfaces. Cetol 23 Plus is a premium, translucent topcoat for Cetol 1.

How long does cetol take to dry?

Drying Time: Touch-dry six (6) – eight (8) hours; dry to walk on after 24 hours minimum at 68º F and 65% relative humidity. Note: During application, moisture content of wood substrate should not exceed 21%. Do not apply when rain, dew, or frost are forecast within five (5) hours of application.

Do I need to sand between coats of Sikkens?

Do not sand between coats, as this product needs the full application thickness from each coat for its UV effectiveness. … Lightly sand the old finish (with the grain) using 220-grit or 320-grit sandpaper. Remove all sanding residue with a vacuum, and apply a maintenance coat of Cetol.

Is sikkens worth the money?

Sikkens is a world class product that is head and shoulders against other deck stains, oils and look alikes. Been using Sikkens for 23 years and have always been satisfied. Not cheap, but worth ever dollar. Takes 24 hours to dry and looks terrific when cured.

Does cetol go bad?

These volitile components will evaporate fairly quickly in warm conditions if the tin is left open, but even if closed, once oxygen has mixed in (the more space in the tin the more oxygen) the products will break down over time (depending on tempreture, product, amount of air that got into the can and time).

Can you recoat cetol?

Cetol SRD should be weathered before recoating. Visually inspect the coating and when it appears faded spray the surface with water. If the water penetrates and the wood turns dark due to the moisture, this is an indication that its time for a new coat of Cetol SRD.

Is sikkens cetol water based?

Sikkens Cetol BLX-Pro is a quick drying water based exterior timber finish that is ideal for decks and outdoor furniture providing good durability and flexibility. Its highly transparent finish accentuates the natural characteristics and colour of the wood.

Is sikkens Rubbol oil based?

To clear up some confusion, this is an acrylic/oil hybrid, not an oil stain. … Rubbol Solid DEK is an acrylic solid stain. Sikkens provides very detailed preparation and applications instructions for their products and they are there for a reason.

Can you stain over sikkens?

If its cetol 1 it shouldn’t be on a deck in the first place. A semi trans won’t penetrate over Cetol 1, that’s your next problem. Only thing you can do without stripping is a solid stain.

Can I paint over sikkens?

Registered. Yes that is what they want to do. Cover with a solid paint over the sikkens.

Who makes Sikkens stain?

Sikkens is part of AkzoNobel, the largest global paint and coatings company and a major producer of specialty chemicals. AkzoNobel supplies industries and consumers worldwide with innovative products and are passionate about developing sustainable answers for our customers.

Is sikkens breathable?

Sikkens ALPHA TEX ACRYL Breathable water-based paint.

How do you maintain Sikkens SRD?

Apply a cleaning solution of four (4) ounces of oxalic acid to one gallon of warm water using a garden sprayer or a heavy nap roller cover. Allow solution to dwell on surface for 20 minutes then thoroughly rise with clean water. Do not allow solution to dry on wood surface.

Do you sand between coats of cetol?

Always allow 24 hours drying time between coats. It is not recommended to sand in between coats of Cetol on exterior wood. This will lower the overall layer thickness, which is very important for effective product performance. For a smoother finish, scuff the surface lightly with a nylon scuffing pad.

How do you use teak sikkens?

For best results, apply in direction of grain with a long haired natural bristle brush. Don’t apply In direct sunlight or when surface is hot to touch. Do not apply in wet weather or when moisture content is greater than 18%. Do not apply Sikkens Cetol Natural Teak Finish below the waterline.

How many coats does cetol 23 have?

After preparation, apply 1 coat of Cetol 1RE and 2 coats of Cetol 23 PlusRE assuring a 24-hour dry time between coats. If possible, back prime with the first coat. During application, saturate all end grains, nail holes, cavities and cracks in the wood.

What cetol 23?

Cetol 23 Plus RE is a translucent topcoat for Cetol 1 RE™. The advanced alkyd resin retains elasticity and offers excellent durability and protection for siding, logs and other vertical surfaces. Key Features: Improved clarity and colour retention. Minimizes occurrence of peeling and blistering.

Can you use sikkens on decking?

Sikkens CETOL® WF 761 is designed for Decking in mind and is a Brushable 1K Waterborne Acrylic, High-build, Tranlucent Stain that can be used as a one pot solution on both exterior and interior stable timber components.