A new pool motor costs $300 on average, with most models ranging from $100 to $500 (materials only). If your pool pump stops working, you might only need to replace the motor instead of the entire system.

How do you know if your pool pump motor is bad?

  1. Age. Yes, the age of your pump is an early trouble sign. …
  2. Noise. Your pool pump should run quietly. …
  3. Power Trip. Has your pool pump motor started to trip your electric breaker box more and more frequently? …
  4. Swimming Pool Pump Motor Keeps Shutting Off. …
  5. Loss of Suction.

How long does a pool pump motor usually last?

Well-maintained high-quality pool pumps can last between eight to 12 years.

Is it worth fixing a pool pump?

When determining the magic number of replacement parts cost versus the cost of the whole pump, we generally suggest 60-75% as the standard. If the cost to repair is within or over this range, it is smarter to replace the pump. This way you have a brand new pump and warranty covering any mishaps down the line.

Can you replace just the motor on a pool pump?

If you have an older pool pump or it’s motor is running loud or just stop working, you’ll want to consider replacing your pool pump motor. You do not have to replace the whole pool pump and as this guide will show, replacing your pool pump motor is not difficult.

What causes pool pumps to fail?

When a pump loses prime, or stops pulling the water to itself, this reduced or nonexistent flow of water causes the motor to run hot. … This loss of prime may be due to air leaks on the incoming pipes, trap cover, low water in the pool, or even a stuck weir door on the skimmer.

What causes a pool pump to burn out?

The impeller is the part of a pool pump that moves the water. A clogged impeller can lead to severely limited flow through the system and could burn out the motor. What causes it? Large debris such as mulch, sticks, and small toys sometimes make it past the pump basket, and can clog up the impeller.

Is a pool pump and motor the same thing?

The guts of the pump are made up of gaskets, impellers, diffusers, and strainer baskets. All these parts make up the wet end but without something to drive these parts, they are merely pieces of well-formed plastic. The part that makes it come to life is the motor.

Is my pool pump dead?

If you hear a pop and a click when turning on the motor, it’s a sign of electrical failure either inside your pump or inside your home. You may need to do some electrical detective work to find out what’s causing the lack of power.

Can pool pump be repaired?

Most of the new generation of pumps are already equipped with automatic controls and safety features. In fact, if you take enough time to learn the manual, you might find yourself able to repair some of the problems on your own. Of course, there are repairs and replacements are best left in the hands of professionals.

Article first time published on

Do pool pumps lose power over time?

Over time, older pumps can begin to deteriorate and lose power. In other cases, you might need to clean the filter or have it backwashed.

What size pool pump do I need for a 30 000 gallon pool?

Calculating Your Swimming Pool Water Pump Needs Now convert that to GPM: 30,000 gallons ÷ 24 hours = 1250 gallons/hour. 1250 gallons/hour ÷ 60 minutes = 20.8 gallons/minute (GPM)

Why is my pool pump so noisy?

One of the most common causes for a noisy pump is that it’s running dry. … If your pool water level has fallen below halfway on the skimmer faceplate, your pump might be sucking in air as well as water. This puts more strain on the pool pump, causing it to work harder—and louder.

Why is my pool motor not working?

If your pump doesn’t turn on OR shuts off quickly after it’s started, it’s probably an electrical problem. … If the pool pump motor shaft isn’t rotating, check to see if the motor is jammed with debris. If the pump turns on but isn’t running full steam and you hear a humming noise, check your capacitor.

When should I replace my pool pump motor?

How long do pool pumps last? Your pool pump should be replaced anywhere between 8 to 15 years depending on the quality, and a full replacement may cost over $800. Your pool pump is the “heart” of your swimming pool as it circulates water throughout, bringing water through the filtration and heating systems.

Can I replace my 1hp pool pump with a 1.5 HP?

You cannot replace a 1.0 full rated motor with a 1.0 uprated motor. However, you can replace your 1.0 Full rated motor with a 1.5 HP uprated motor. This is because they both will have the same total horsepower.

How do I know if my pool pump is overheating?

The first test is simply whether you can touch the motor or not. Under normal operating conditions, the motor end of the pump is hot enough that you can barely touch it — but not searing hot. If you check your pool pump motor and find it is far too hot to be able to touch with your hand, that’s not good.

What causes a pool motor to seize?

If the shaft does not spin, the motor is seized internally or is being restricted by a pump component. … If the motor is removed from the pump and is receiving power but not turning over, the pump motor may be seized. Bearings and windings can seize and rust, especially during long periods of inactivity.

Why is my pool pump humming and not working?

Some of the most common reasons are that: You might have a bad capacitor. Debris might be blocking the impeller and consequently disabling the pool pump. There might be problems with the motor shaft.

How do I know if pool pump is working?

Given enough time, you will not want to even touch the water because it’ll look like a swamp. If your water looks good and the water in your pool is moving well, then your pump is working.

What happens if your pool pump is too big?

Too large of a pump can cause poor filter performance and even damage it, if the filter is not also oversized accordingly. Another possible consequence is pump cavitation in which bubbles form in the water inside the pump and then burst with great force, resulting in damage to the impeller and other internal parts.

How many gallons per minute does a 2 HP pump?

Table of Submersible Pump Stages vs HP vs Total Dynamic Head vs. GPM Flow Rate CapacityWater Pump HPNr. of Pump StagesGPM Flow Rate Capacity1 1/2 HP114 – 40 GPM (varies by TDH)2 HP144 – 42 GPM (varies by TDH)3 HP194 – 43 GPM (varies by TDH)

How long should I run my above ground pool pump?

As long as it runs for at least 8 hours in every 24-hour period, you’re good to go. Overall, the lessons learned today is you should run your pool pump an average 8 hours a day to properly circulate and clean your water. The pump should push your entire pool in gallons in this 8 hour period of time.

How do I quiet my pool pump motor?

  1. Reduce the Vibrations of your Pool Pump’s Motor. …
  2. Clean the Skimmer Basket Regularly. …
  3. Try Raising the Level of Water in the Pool. …
  4. Keep Your Pool Pump Basket Clean. …
  5. Keep Your Impeller Clean. …
  6. Replace the Bearings on the Pool Pump Motor. …
  7. Replace the Whole Pool Pump.

What does a bad pool pump sound like?

Pool pumps sometimes make grinding noises. This can sound like stones rattling inside the pump, or it can sound a little like a coffee grinder grinding beans. Again, this sound can be a sign that your baskets need cleaning out. Grinding sounds are often from a lack of water moving through the pump.

Do you leave a pool pump on all the time?

Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. … If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

How do I reset my pool pump?

  1. Turn off the pump. …
  2. Switch to recirculate. …
  3. Release air. …
  4. Clean out the pump basket. …
  5. Fill the pump basket. …
  6. Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on.
  7. Check the water flow to your pump.