Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Does roofing felt go under or over flashing?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Does the drip edge go over the felt?

At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.

Does flashing go over or under underlayment?

According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof. Understanding the proper way to install the drip edge will only get you so far.

Where does flashing on a roof go?

  1. Roof flashing is a thin metal material that roofers install to direct water away from certain areas (walls, chimneys, roof valleys) of your roof. …
  2. Installing flashing anywhere your shingles butt up against something, such as a wall, chimney, or in open roof valleys is crucial to the life of your roof investment.

Which side of roofing felt goes down?

Direction. When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper’s two sides are noticeably different. One side is somewhat sticky, though don’t expect it to leave a glue-like residue on your hands.

What is the proper overhang for roof shingles?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

Is drip edge and flashing the same thing?

Drip edges are metal sheets, usually shaped like an “L,” installed at the edge of the roof. Also called drip edge flashing or D-metal, they serve a vital function by directing water away from the fascia and into the gutter.

Does underlayment go over ice and water shield?

You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing. If two courses of IKO’s ice and water protector are needed widthwise, you should apply the bottom course first.

Where does drip edge go on a roof?

The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.

Article first time published on

Should drip edge be tight to fascia?

A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.

How do you seal roof flashing?

Renew flashing seals by chipping out the old mortar and caulking along the edges of the flashing. Use special masonry caulk to seal the joints between the flashing and the chimney. Seal the seam between the cap and step flashing with urethane roofing cement or silicone caulking compound, as shown at right.

Is roof flashing necessary?

Roof flashing, usually made from metals like aluminum, copper, or steel, is flat and thin, and prevents water from getting under shingles. … All of these areas leave shingles and underlayment vulnerable to water, so the flashing is necessary to prevent leaks.

How much should a starter overhang for shingles?

Starter shingles should always overhang the eave and rake edges of the roof by about 1/4″-3/4″ to ensure adequate rain water drainage. It is also important that the seal strip is placed facing up and close to the edge of your roof; otherwise, your roofing system won’t seal properly.

Do shingles have to overhang drip edge?

Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.

How far should shingles overhang gutters?

Shingle Overhang Often Has to Be Addressed Most shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.

Do you nail or staple roofing felt?

Some roofers prefer to attach felt underlayment with 1-inch roofing nails or special nails with plastic washers, but most codes allow staples, which are easier to drive.

How do you finish felt edges?

  1. More washing. Using a washboard or solar pool cover to provide the maximum agitation, wash and scrub just the edges. …
  2. Roll with doweling. …
  3. Furl the edges. …
  4. Ironing the felt flat. …
  5. Cut a straight edges around the felt. …
  6. Felt areas to shrink them straight. …
  7. Furl the edges of the felt. …
  8. Pull the felt into shape.

Can you add flashing to an existing roof?

Flashing is generally installed at any joints or edges in the roof where water could otherwise work its way in. In order to properly install new flashing, you’ll have to remove the shingles surrounding your old flashing, and then re-lay them after installation.

How does flashing work on a roof?

Flashing is a flat and thin material used to prevent water from entering the openings and cracks of a roof. It is placed underneath the shingles of your roof and it redirects the water to another location. Roof flashing is made from metals, such as copper, aluminum, stainless steel, or galvanized steel.

Do you need felt paper over ice and water shield?

Tim wrote in asking if he should use roofing paper on his roof in addition to Ice and Water shield. … It is not absolutely necessary but it is extra protection over that area of the roof that could potentially have water backing up from roof edge ice dams, up and under the shingles.

Does felt go over ice and water?

Felt over the ice and water, yes. Depending on the type of ice/water use, you may never get the shingles removed if you get to be so lucky as to reroof the thing in 20 yrs.

Where should ice and water shield be installed?

  1. On the eaves of your home up to 24″ inside the exterior wall (this usually means at least 2 rows or 6 feet)
  2. In every valley (1 row or 3 feet)
  3. Around every pipe before the flashing is installed.
  4. Along every wall, chimney, or skylight where flashing will be installed.

Do I need drip edge flashing?

It helps direct rainwater off of the roof, either into a gutter or onto the ground. Without the flashing, rainwater could adhere to the edges of the roof and saturate important structural components. Drip edge flashing helps protect the roof decking, wood soffits, and wood trim from rot.

Can you install new drip edge over old drip edge?

Replacing Drip Edge Eave Strips: Align one end of the lower eave strip even with the edge of the roof decking. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails. Overlap the other pieces of eave strip by at least 1” and nail them in place.

Do gutters go over or under drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. … If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

Does roof flashing need to be sealed?

As long as the flashing has been installed properly, you can repair a leaking seam using simple roofing cement in most instances. Simply push the seam back down and secure it in place with screws if necessary, and then apply roofing cement around all the edges of the flashing for a watertight seal.

Should you caulk roof flashing?

Roof flashings can be made from thin metal, rubber, and a few other materials. … It’s okay to use caulk and roofing cement as a last resort to make a temporary leak repair, but don’t allow a roofer to convince you they’ll work for the long term.

Should you caulk flashing?

Flashing acts as a waterproofing layer for this type of siding, and caulking will prevent the flashing from doing its job. As far as trim boards are concerned, you should not caulk around these areas if they sit on top of the surface of your siding.